Chemical and physical data |
Typical values |
| Activity |
90 % |
| Density |
0.42 g/cm³ @ 25C |
| Water Soluble Salts % |
5 % |
|
| The specifications and properties listed above are intended for products
manufactured in USA. |
| Advantages |
| Morwet® D-390 is a blend of an alkyl naphthalene sulfonate condensate plus
lignosulfonate. The blend will function as a dispersant for Suspension
Concentrates, Wettable Powders and Water Dispersible Granules. Morwet®
D-390 might also function as a dispersant for Suspoemulsions and as an
emulsifier for microencapsulation. |
| Further Information |
| For further information, technical service and samples, please contact our
nearest Akzo Nobel Sales office or agent/distributor. |
|
| MORWET D-425 POWDER |
Morwet D-425 Powder is a sodium salt of naphthalene sulfonate condensate(NSC). |
| Specification |
|
Limits
|
Method
|
| Active content |
min 88.0% |
* |
| Appearance, 25°C |
powder |
* |
| Moisture |
max 4.0% |
* |
| pH, 5% in water |
7.5-10.0 |
* |
| Salt content |
7.0-9.0% |
* |
|
| *Methods of analysis can be received upon request. |
| Typical data |
Surface active characteristics |
Typical values |
| Wetting power according to Draves, 25°C, 0.1% |
>5min |
| Surface tension according to Du Noüy, 25°C, 0.1% DIN
53914 |
60 mN/m |
| Foam height, according to Ross-Miles, 25°C, 0.05% in
de-ionised water |
initial: 70 mm
after 5 min: 25 mm |
| Foam height, according to Ross-Miles, 25°C, 0.05% in
Standard Water D |
initial: 40 mm
after 5 min: 30 mm |
|
| The specifications and properties listed above are intended for products
manufactured in USA. |
| EPA classification |
| Exempt from tolerance under EPA regulation 40 CFR 180.1001 (d) |
| Application |
| Morwet D-425 Powder is suggested for use as dispersant in SC, WDG and WP. |
| Further Information |
| For further information, technical service and samples, please contact our
nearest Akzo Nobel Sales office or agent/distributor. |
Wetting Agents |
Wetting Agents are addded to dry formulation to assist granule breakdown and enhance bloom or sponaneity of granule dispersion into water. Rapid Granule breakdown allow the dispersants to perform more effectively and create a better suspension from the application.
Morwet Wetting Agents offer superior wetting, even at low concentrations, and offer versatile wetting properties. There excellent surface tension reduction and very fast wetting characteristics help the formulator to achieve better suspensibility, bloom, and resuspensibility in dry flowable formulation. Certain products also can be used as wetting agents in microencapsulation products and processes. |
| MORWET EFW POWDER |
| Specification |
|
Limits
|
Method
|
| Active content |
min 95.0% |
* |
| Appearance, 25°C |
powder |
* |
| Moisture |
max 2.0% |
* |
| pH, 5% in water |
7.5-10.0 |
* |
| Salt content |
max 2.5% |
* |
|
| *Methods of analysis can be received upon request. |
| Typical data |
Surface active characteristics |
Typical values |
| Wetting power according to Draves, 25°C, 0.1% |
17 sec |
| Surface tension according to Du Noüy, 25°C, 0.1%
DIN 53914 |
32 mN/m |
| Foam height, according to Ross-Miles, 25°C, 0.05%
in de-ionised water |
initial: 120 mm
after 5 min: 60 mm |
| Foam height, according to Ross-Miles, 25°C, 0.05%
in Standard Water D |
initial: 30 mm
after 5 min: 10 mm |
|
| *Methods of analysis can be received upon request. |
| Typical data |
| Exempt from tolerance under EPA regulation CFR 180.1001 (c) |
| Application |
| Morwet EFW Powder is a wetting agent used with Morwet D-425 (dispersant)
to assist granular break-down in highly concentrated systems, effective at low
use rates, products will demonstrate different suspensibilities based on different
technicals. |
| Further Information |
| For further information, technical service and samples, please contact our
nearest Akzo Nobel Sales office or agent/distributor. |
| MORWET IP POWDER |
| Specification |
|
Limits
|
Method
|
| Activity |
75 % min |
* |
| Appearance (25°C) |
Tan Powder @ 25C max |
* |
| Moisture |
2.5 % max |
* |
| pH, 5% solids |
7.5 - 10 |
* |
| Salt (NaCl) |
18 % max |
* |
| Unsulfonated oil |
8 % max |
* |
|
| *Methods of analysis can be received upon request. |
| Typical data |
Surface active characteristics |
Typical values |
| Bulk Density |
1.10 - 1.20 g/cc |
|
| The specifications and properties listed above are intended for products manufactured in USA. |
| Further Information |
For further information, technical service and samples, please contact our nearest Akzo Nobel
Sales office or agent/distributor.
|
Adjuvants |
| ADSEE907 |
Adujant: a material added to a tank mix to aid or modify the action of an agrichemical, or the physical characteristics of the mixture.
Adujant: any substance in a herbicide formulation or added to the spray tank to modify herbicidal actuvity or application characteristics. |
| Adsee 907 is a wetting agents intended for improvement of the efficiency of herbicides when applying to the crop. |
| Specification |
|
Limits
|
Method
|
| Appearance, 20°C |
Yellow-Brown Liquid |
* |
| Colour |
4-9 Gardner |
* |
| Total Basic Nitrogen |
1.04-1.13% |
* |
|
| Typical data |
Chemical And Physical Data |
Typical values |
| Density, 20°C |
1055 kg/m³ |
| Flash Point |
>100°C |
| pH,1% in water |
9-10.5 |
| Pour Point |
10°C |
| Viscosity, 20°C |
300 mPa.s |
|
| Solubility |
| The solubility of 5% Adsee 907 at 25°C is as follows: |
| Isopropanol |
Soluble |
| Mineral Oil |
insoluble |
| Solvesso 150 |
insoluble |
| Soy bean oil |
insoluble |
| Water |
Soluble |
| Xylene |
insoluble |
|
| The specifications and properties listed above are intended for products manufactured in Europe. |
|
